Tyros3
Owner's Manual


6
Registration Memory
- Saving and Recalling Custom Panel Setups -

The Registration Memory function allows you to save (or "register") virtually all panel settings to a Registration Memory button, and then instantly recall your custom panel settings by simply pressing a single button. The registered settings for eight Registration Memory buttons should be saved as a single Bank (file).

Registering Your Panel Setups

1	Set up the panel controls (such as Voice, Style, effects, and so on) as desired.

2	Press the [MEMORY] button above the REGISTRATION MEMORY section.
The display for selecting the items to be registered appears.

3	Determine the items you want to register.
Select the desired item by using the [2 UP DOWN] to [7 UP DOWN] buttons, then enter or remove the checkmark by using the [8 UP] (MARK ON)/ [8 DOWN] (MARK OFF) buttons.
To cancel the operation, press the [I] (CANCEL) button.

4	Press one of the REGISTRATION MEMORY [1] to [8] buttons to which you wish to memorize the panel setup.
The memorized button becomes red, which indicates the number button contains data and its number is selected.

CAUTION
If you select the button whose lamp is lit in red or green here, the panel setup previously memorized to the button will be erased and replaced by the new settings.

About the lamp status
Red: Data registered and currently selected
Green: Data registered but not currently selected
Off: No data registered

5	Register various panel setups to other buttons by repeating steps 1 to 4.
The registered panel setups can be recalled by simply pressing the desired number button.

NOTE
The panel setups registered in the numbered buttons are preserved even when you turn off the power. If you want to delete all the eight current panel setups, turn the [POWER] button on while holding the B5 key (right-most B key on the keyboard).

Saving the Registration Memory as a Bank file
You can save all the eight registered panel setups as a single Registration Memory Bank file.

(Figure)
Bank 01
Bank 02
Bank 03
Bank 04

1	Press the REGIST BANK [plus] and [minus] buttons simultaneously to call up the Registration Bank Selection Display.

2	Press the [6 DOWN] (SAVE) button to save the Bank file (page 30).

Recalling a Registered Panel Setup
The saved Registration Memory Bank files can be recalled by using the REGIST BANK [minus]/[plus] buttons or the following procedure.

1	Press the REGIST BANK [plus] and [minus] buttons simultaneously to call up the REGISTRATION BANK Selection Display.

NOTE
Turning the [FREEZE] button on disables recall of specific item(s). To use this function, you need to select the item(s) not to be recalled by accessing [FUNCTION] -> [E] REGIST SEQUENCE/FREEZE/VOICE SET -> TAB [LEFT][RIGHT] FREEZE.

2	Press one of the [A] to [J] buttons to select a Bank.

3	Press one of the green-lit numbered buttons ([1] to [8]) in the Registration Memory section.

Confirming the Registration Memory Information
You can call up the information display to take a look which Voices and Style are memorized to the [1] to [8] buttons of a Registration Memory Bank.

1	Simultaneously press the REGIST BANK [plus] and [minus] buttons to call up the Registration Bank Selection display, then use the [A] to [J] buttons to select the desired Bank. 
You can also use the [DATA ENTRY] dial and the [ENTER] button to select a Bank.

NOTE
You can instantly call up the information display of the currently selected Registration Memory Bank by pressing the [DIRECT ACCESS] button and one of the REGISTRATION MEMORY [1] to [8] buttons in sequence. 

2	Press the [6 UP] (INFO) button to call up the information display.

By using the TAB [LEFT][RIGHT] buttons, you can switch between the two information display pages: information for the Registration Memory [1] to [4] buttons and information for the [5] to [8] buttons.

NOTE
The grayed Voice indicates that the corresponding Voice part is off, while black indicates the part is on.

3	Press the [F] (CLOSE) button to close the information display.

(Table)
Advanced Features	Refer to the Reference Manual on the website.
Disabling recall of specific items:	[FUNCTION] -> [E] REGIST SEQUENCE/FREEZE/VOICE SET -> TAB [LEFT][RIGHT] FREEZE
Calling up Registration Memory numbers in order:	[FUNCTION] -> [E] REGIST SEQUENCE/FREEZE/VOICE SET -> TAB [LEFT][RIGHT] REGISTRATION SEQUENCE
(Table End)


This is the end of the file.